Robofocus controller. Included are the corresponding stepper motor and the RF3 control unit, standard adapter and cables, the PC software on CD and a manual in English. g. The RoboFocus system (photo above, from the Technical Innovations web site) comes with a small control box, which allows manual focusing, as well as connecting the computer, the stepper motor, and the remote power module. 00 Product Description: Computer-based dome automation package, hardware, and software. Lack of development from the manufacturer for many years means that the focuser is abandonned. Provides complete remote control capability of observatory including slaving to the telescope. Introduction The RoboFocus is a remote focus driver to be installed on your existing focus mechanism. , FocusMax) can drive the RoboFocus system. Takahashi has standardized with an 8mm diameter shaft on both the 2. 7-inch and 4-inch focusers. v3 drivers have temperature but don't save settings well and are a bit unstable. 1 at a fixed cost. RoboFocus RF3 Upgrade - RFU Owners of earlier Model 1 and Model 2 RoboFocus control units can have these devices upgraded to version 3. A small brass coupler (with a built-in “clutch” on the motor side), attaches the motor directly to this shaft and is held into place with two set screws Automation Products Product Name: Digital Dome Works Part Number: DDW Price (US $): 2,400. Robofocus controller through ASCOM Having a Robofocus, I ran into a few problems with the various drivers I could find: v1 drivers didn't have access to temperature. Accessories – Observatory motor drive systems, power supplies, dome upgrades, small parts, and add-ons including products from other vendors matched to our observatories. RoboFocus About RoboFocus RoboFocus is a remote focus driver that installs on your telescope’s existing focus mechanism. Software and drivers for the Seletek family of controllers. 00 Product Description: The RoboFocus control module can be purchased separately for $330 as a backup unit or combined with an additional motor kit that was previously obtained. The RoboFocus software can be used, or other focusing software (e. 00 Product Description: Complete RoboFocus system, ready to install and operate on your specific telescope/focuser. RoboFocus provides digital control and feedback of the focus position using a stepping motor controlled by a microprocessor. System includes custom designed stepper motor, RF3 control module, mounting hardware (brackets, shaft coupler, and/or timing sprocket), power converter/adapter (110vAC to 12vDC), cables, PC software (on CD) and comprehensive instruction manual. Separate ASCOM drivers are supplied for up to three simultaneous devices (focuser, rotator, dome). Robofocus can communicate via ASCOM and be controlled by a computer. Complete RoboFocus system, ready to install and operate on your specific telescope/focuser. This price includes complete bench testing and "field" operation test. 2 Instructional User Manual Robofocus User Manual 6 Foot Home Dome Manual & 6 Foot Pro Dome Manual 10 Foot Home Dome Manual & 10 Foot Pro Dome Manual 15 Foot Home Dome Manual & 15 Foot Pro Dome Manual. Automation – DDW (the #1 observatory automation package), Dome Works, RoboFocus, and other automation devices. Product Name: RoboFocus Part Number: RF3 Price (US $): 495. The RoboFocus control module can be purchased separately as a backup unit or to combine with an additional motor kit that was previously obtained. The "in/out" buttons move the stepper motor to achieve visual focus. Product Name: RF3 Controller & Cables Part Number: RFC Price (US $): 355. The user sends commands from his computer to the RoboFocus to move the focus, and receives back digital position The RoboFocus is a remote focus driver to be installed on your existing focus mechanism. The most common Takahashi RoboFocus install is the Rack & Pinion setup, mounted directly onto the focus shaft, after removing one wheel knob. These buttons are duplicates of the ones on the RoboFocus controller box. The user sends commands from his computer to the RoboFocus to move the focus, and receives back digital position Technical Innovations Publication Downloads “At Home In A Dome” Publication “Remote Control Handbook” Publication DDW 5. The system includes a custom-designed stepper motor, RF3 control module, mounting hardware (brackets, shaft coupler, and/or timing sprocket), and power converter/adapter (110vAC to 12vDC), cables, PC software (on CD), and Includes the main controller and the supplemental RF3 hand paddle. The RF3 Hand Paddle allows manual focusing via a small hand controller on a 12 foot cable. This upgrade includes the replacement of 3 IC chips, new firmware and two circuit board upgrades. Robofocus RF3 - Motorized focus for almost any focuser The complete Robofocus system is ready for adaptation to almost any focuser. idf ufpy rapfmb yzdmx epkkh drolt hnozjd dsxol oyitv wlupbwj